Products > FM-200 > FM-200 Fire Suppression System

FM-200 Fire Suppression System

FM200 fire suppression system is a clean,colorless,and environmentally friendly fire suppression agent that is electrically non-conductive and safe for humans.It extinguishers flame primarily through heat absorption,leaving no residue,thus minimizing downtime after a fire and making FM-200 suppression systems acccepted and respected worldwide with over one hundred thousand installations in more than seventy countries.

Share

FM-200 Fire Suppression System

 

DESCRIPTION

The FM-200 Fire Suppression System is an engineered system utilizing a fixed nozzle agent distribution network. The system is designed and installed in accordance with the National Fire Protection Association (NFPA) Standard 2001, “Clean Agent Fire Extinguishing Systems.” When properly designed, the FM-200 system will suppress surface burning fire in Class A, B, and C hazards.

 

Complete suppression using FM-200 has the following advantages:

FM200 gas is clean agent, the system is environmental fire suppression system

• The small quantity of agent cover maximum protected area.

• Maximum safety for personnel due to low toxicity.

• Most effective when used with automatic detection to introduce FM-200 rapidly.

• The ability to prevent re-ignition as long as concentration levels are maintained.

 

Typical areas that can be protected by a FM-200 system are:

Bank Vaults                                  Libraries

Rare Book Stores                      Electronic Data Processing

Telephone Exchanges                Studios

Communication Centers            Transformer and Switchrooms

Control Rooms                         Test Laboratories

Armarium Rooms                     Flammable Liquid Storage        

 

CATEGORY

WINAN FIRE has three types of FM200 suppression system available, they are pipe network type, cabinet type and hanging type.

1. Pipe network type

This type consists of extinguishing agent stored in high strength steel cylinders. Manual or automatic actuators are available to open the valve(s) for release of the agent into the hazard area. The agent is distributed and discharged into the hazard area through fixed piping and nozzles. Each nozzle is designed to deliver a uniform discharge of agent into the protected area. On large hazards, cylinders can be manifolded together. The cylinders are connected to the manifold by means of a flexible discharge bend and check valve. Automatic actuation is accomplished through the detection system. When a fire condition cause the detector(s) located in the hazard area to go into alarm, a signal is sent to the detection control panel. This causes actuation of the release circuit which electrically operates the actuator located on the cylinder valve. The actuator opens the valve and allows the agent to enter the pipe network and discharge out the nozzles.

This type of system can protect as many as 8 hazard areas at once. The system will be located in a separate room partitioned from protected areas.

                                               

 

PARAMETER

Model

QMQ4.2/70N-GA, QMQ4.2/90N-GA,   QMQ4.2/100N-GA, QMQ4.2/120N-GA, QMQ4.2/150N-GA,



Cylinder Capacity

70L, 90L, 100L,   120L, 150L


Agent Type

HFC-227ea   (FM200)


Agent Filling Density

950KG/m³


Storage Pressure

4.2MPa


Maximum Working Pressure

5.3MPa


Starting Voltage/Current

DC24V/1.6A


Operation Temperature

0-50°C


Starting Mode

Auto/Manual


 

Cabinet Type

Compared with pipe network type, construction of cabinet type is more simple. Only consists of cabinet, cylinder (with solenoid valve) and discharge nozzle. Gas cylinder was installed inside the cabinet. Discharge nozzle installed on cabinet. This type with good aesthetics and convenient transportation. The starting mode is same as pipe networking type. The system receive the signal from fire detector(s) to stimulate solenoid valve open and agent discharge out from nozzle into hazard area.

This type of system will be located in the same room of hazard area. Every set of cabinet is a complete and independent system covers one protected area only.     

 

PARAMETER FOR Single Cylinder

Model

Cylinder   Capacity

(L)

Dimensions (mm)

H×L×B

GQQ40/2.5GA

40

1300×450×450

GQQ70/2.5GA

70

1600×500×450

GQQ90/2.5GA

90

1800×500×450

GQQ100/2.5GA

100

1800×550×450

GQQ120/2.5GA

120

1900×580×520

GQQ150/2.5GA

150

1900×580×520

GQQ180/2.5GA

180

2100×650×600

PARAMETER FOR double Cylinder

Model

Cylinder   Capacity
  (L)

Dimensions (mm)

H×L×B

GQQ40/2.5GA

40

1300×840×450

GQQ70/2.5GA

70

1600×930×450

GQQ90/2.5GA

90

1800×930×450

GQQ100/2.5GA

100

1800×930×450

GQQ120/2.5GA

120

1900×1100×520

GQQ150/2.5GA

150

1900×110×520


Hanging Type

Hanging type FM200 system is capable for computer room, switch board room, small oil depot or such small protected areas. Hanging type FM200 system has two starting modes. One is same as cabinet type by solenoid valve. Another mode activated through a bulb sprinkler head. The cylinder is sealed by a glass bulb sprinkler. Same mechanism as fire sprinkler, a fire condition cause environment temperature increase. When temperature gets bulb rated temperature, glass bulb burst and seal falls. Agent discharge to hazard area from sprinkler head.

Hanging FM200 system can be either hung on the ceiling or mounted on the wall, which depends on spatial position of the protected room.



PARAMETER

Model

Cylinder   Capacity

(L)

Dimensions (mm)

Storage Pressure   (20°C)

(MPa)

Starting Mode

H×L×B

QQC8/1.6

8

Φ260×300

1.6

solenoid   valve/glass bulb

QQC10/1.6

10

Φ300×356

1.6

solenoid   valve/glass bulb

QQC15/1.6

15

Φ330×427

1.6

solenoid   valve/glass bulb

QQC20/1.6

20

Φ330×427

1.6

solenoid   valve/glass bulb

QQC30/1.6

30

Φ400×437

1.6

solenoid   valve/glass bulb

 

 

 


Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit
Previous: Fire Suit
Next: Rubber Bladder